SCG353A047 1.5Inch right angle 24VDC 220VAC 2/2 way valve pulse
FEATURES
• The pulse diaphragm valves are especially designed for dust collector service applications,
combining high flow, long life and extremely fast opening and
closing to produce reliable and economical operation
• The high flow, angle type bodies in combination with the special main diaphragm assemblies give
theunique operating features required for dust collector service
applications
• The design with integral compression fittings will facilitate installation because there is no need for threaded
piping
• The high quality diaphragms are reinforced and wear resistant to guarantee a long operating
life, even under harsh conditions
• Integral pilot operated valves satisfy all relevant EC directives
| Ordering Code | Port Size | Orifice | Flow Value | Coil type |
| G Threaded | mm | m3/h | l/min |
| SCG353A047 | 1 1/2" | 52 | 46 | 768 | 400425 |
| SCG353A050 | 2" | 66 | 77 | 1290 | 400425 |
| SCG353A051 | 2 1/2" | 66 | 92 | 1540 | 400425 |
| SCG353.060 | 3" | 75 | 170 | 2833 | 400425 |
| Construction |
| Body | Aluminum |
| Core tube | Stainless steel |
| Core and Plugnut | Stainless steel |
| Core Spring | Stainless steel |
| Sealing & disc | CR (chloroprene) |
| Diaphragm | NBR(nitrile/buna-n) |
| Shading coil | Copper |
| Connector | DIN43650A |
| Voltage | DC: 24V, AC: 24V,48V,110V,230V |
| Working Temperature | -20 to +85℃ |
| Protection Class | IP65 |
| Coil Insulation Class | F |
| Working Pressure | 0.35-0.85Mpa |
| Ordering Code | A | B | C | D | E | F | G | H | J | K | L | Weight |
| SCG353A047 | 80 | 50 | 30 | 71 | 130 | 136 | 45 | G 3/8" | 131 | 160 | 178 | 1.40 |
| SCG353A050 | 80 | 50 | 30 | 95 | 168 | 165 | 45 | G 3/8" | 165 | 210 | 227 | 2.90 |
| SCG353A051 | 80 | 50 | 30 | 95 | 168 | 165 | 45 | G 3/8" | 165 | 210 | 227 | 2.60 |
| SCG353.060 | 80 | 50 | 30 | 143 | 240 | 192 | 45 | G 1/2" | 165 | 258 | 275 | 4.10 |
After-sale Service
We can provide a series of after-sale service, such as product
introduction, mounting, debugging, technical support and so on.
Warranty
All item Comes with Basic 3 Month Sellers Warranty, if item
defective in 3 Month, We will offer replacement without extra
Charger(including shipping fee)After we Receive the Defective item.
If item Defective after 3 Month, Buyers can still send it back, We
will contact suppliers or Manufactory for Warranty. Buyers Might
Need to pay the Shipping fee For resend the replaced item.
The installment introduction:
1. First, Confirm the pulse valve in good condition and then
installed
2. Pulse valve will be installed directly the outer wall of flange
of gas manifold. The spray pipe across the gas manifold. According
to the drawing and manual, the pulse valve matching appropriate
spray pipe and installation. To avoid the valve install in the air
manifold bottom. If the pulse valve matched trachea and connector,
the connector will be used for sealing purpose only. It can not as
structural support components. It can not rely on the straight
connector fixed spray torch and package. The spray pipe and air
manifold must be fixed independent.
3. To tighten the hard nut, the maximum torque of 20 N*m.Tighten
the trachea, torsion of 20 N*m.
4. The connection control wire needs connect of every electric
control valve seat. Pay attention to the line adown to prevent rain
waterproof. Or through the joint and nylon pipe, it will connect
the pulse valve and electromagnetic assembly boxes of nylon pipe
connection.
5. To ensure that provide compressed air clean and dry. The air
manifold system provides moderate pressure and check for leaks
installation. ( it can brush on soap and water, check whether the
interface is bubble). Pressure was carried out on the air bag
inflated (pressure of the valve is around 0.03 ~ 0. 86 mpa),
recommend for air pressure 0.8 mpa maximum
6. Testing the pulse valve blowing, listening all the pilot valve
whether it is normal operation and whether the pulse blowing sound
is clear.
